However, mono sound design has many valid applications in contemporary spaces, such as places of worship. Perhaps the most important difference between a point source speaker and other types of speaker systems is how sound is routed through the room. A line array speaker system, especially with multiple speakers arranged in one vertical line, has much more control over the speaker rentals miami sound direction than a point source speaker. This can be a problem when you’re trying to make sure that the audience in a large venue hears uniform levels and sound quality. Electrostatics are inherent dipole radiators and, due to the thin flexible membrane, are less suitable for use in cabinets to reduce low-frequency cancellation as with ordinary cone controllers.
Therefore, an inline power amplifier should be placed between the audio source and the passive speaker to increase the audio signal at speaker level. The variable magnetic field of the voice coil takes place within the permanent magnetic field of the conductor’s magnets. This interaction causes the voice coil to oscillate in a way that mimics the waveform of the audio signal. We will discuss the different types of drivers and how they are designed to convert audio into sound.
If you are considering a speaker system with a speaker for your event space, you should consider the following points. Because a point source speaker is designed to convey the full sound range of a single speaker, it’s an ideal choice for small or medium-sized venues that often host events such as lectures. These speaker systems also require a less invasive installation compared to line array speaker systems and are a great option for smaller venues that need to amplify sound from a microphone easily. For example, a worship service would benefit more from a point-source speaker system.
For example, the spoken word can be isolated to the central channels, while music can be sent to the left and right channels. The biggest advantage that mono sound design systems have over others is the clarity of the sound delivered, especially with a single sound stream coming from the spoken word. Speaking in a stereo sound system, which is designed to provide a richness and depth of sound, can cause speech to be lost or difficult to decipher. However, mono sound systems offer great speech quality and can even be implemented in more contemporary sound systems to ensure that sound travels at equal levels to all parts of a room.
However, a rigid housing reflects the sound internally, which can then be transmitted through the speaker’s diaphragm, again resulting in the deterioration of sound quality. This can be reduced by internal absorption using absorption materials (often called “cushioning”), such as glass wool, wool or synthetic fiber fittings, in the housing. The interior shape of the case can also be designed to reduce this by reflecting sounds away from the speaker’s diaphragm, where they can then be absorbed. The crossover is used in multi-controller speaker systems and is a set of filters that separate the input signal into different frequency ranges (i.e., “bands”), according to the requirements of each controller. Therefore, the controllers only receive power at their operating frequency, reducing distortion in the controllers and interference between them. Ideal features of a crossover can include perfect out-of-band damping at the output of each filter, no amplitude variation (“ripple”) within each stepband, no phase delay between overlapping frequency bands, to name a few.
This is another type of speaker where the name rather describes the design. Most bookshelf speakers have a woofer, usually about 5.25 inches in diameter, and a one-inch tweeter in a two-way setup, although some, like ELAC’s Uni-fi UB5, offer a trio of drivers in a three-way crossover setup. While they don’t have as much power as floor speakers, you still get plenty of sound from a pair of high-quality bookshelf speakers. It is a speaker system where multiple speakers project the sound from the same axis.
The conductor moves a flexible cone, or diaphragm, back and forth very quickly to produce these sound waves. The membrane is normally made of paper, plastic or metal and is attached to the wide end of the suspension and is occasionally more of a dome than a cone. The suspension, also called the envelope, is a flexible metal edge that allows the cone to move.
When choosing a speaker system to integrate into your AVL build, you have many quality options to choose from. While many types of speaker systems offer sharp audio, you need to familiarize yourself with each type, the advantages, and the potential drawbacks. Our audio experts encourage you to consider how a line array speaker system, point source speaker system, and speaker system can optimize sound quality in your theater, event space, or office. Instead of moving back and forth as conventional speakers do, the cone rippled and created sound in a way known in RF electronics as a “transmission line.” The new speaker created a cylindrical sound field. Ohm Acoustics has since produced several models of loudspeakers using the Walsh controller design. German Physiks, an audio equipment company in Germany, also produces loudspeakers using this approach.
Tags: speakers, types